Washing Machine Loud Noise During Spin
Banging, grinding, or thumping sound during the spin cycle
60% chance this is caused by:
Worn drum bearings or damaged shock absorbers
Washing Machine loud noise during spin is a hard-difficulty repair. The most likely cause is worn drum bearings or damaged shock absorbers, and replacing the failed part takes approximately 1-2 hours. The part costs about $75 — compared to $600-1,200 for a full replacement.
Fix it this weekend. Most parts ship same-day on Amazon.
A service call costs $150-300. This repair takes about 1-2 hours and the part runs $75. Order the part tonight, fix it Saturday morning.
✓ Good call investigating this. Most homeowners wait until the problem gets worse — which typically means a higher repair bill. This is a hard-rated repair — 35% of homeowners with basic tools complete it successfully. A $75 part saves you a $150–300 service call.
The exact part you need is listed below — order it now and fix it this weekend.
Safety Warning
Always unplug before servicing. Washing machines are heavy — have someone help you tilt or move the machine. Water may remain in the drum even after draining.
🔧 The Exact Part You Need
Total parts cost: $75. Same-day shipping available on most items.
What happens if you don't fix this
A $75 part now can prevent a much bigger problem later. Left unfixed, this issue can cascade into a $$600-1,200 replacement — that's × the cost of the part. The repair gets more expensive the longer you wait.
Find the Right Part for Your Washing Machine
Parts vary by model. Search with your model number for the best match.
Tip: Add your model number (e.g. "GE GSS25GSH") for more precise results.
🔥 Parts for Washing Machines move fast on Amazon — especially common failure parts like these.
🔨 Tools You'll Need
Repair Summary
| Appliance | Washing Machine |
| Problem | Loud Noise During Spin |
| Diagnosis Confidence | 60% |
| Most Likely Cause | Worn drum bearings or damaged shock absorbers |
| Difficulty | hard |
| Estimated Time | 1-2 hours |
| Parts Cost | $75 |
| Replacement Cost | $600-1,200 |
📋 Step-by-Step Instructions
Unplug the machine
Open back panel to access shock absorbers
Check if shocks are leaking or have no resistance — replace if so
If noise persists, check drum bearings by spinning drum by hand
Grinding from back center = bad bearings
Bearing replacement requires disassembling the outer drum
Don't put this off.
A Washing Machine that's failing can cause water damage, electrical issues, or food spoilage — each costing 10x what the replacement part costs. The fix is straightforward. The part is cheap. The risk of waiting isn't.
🔍 Why This Happens
Root cause analysis for your washing machine's loud noise during spin
The shock absorbers (2-pack) in your washing machine has failed due to a combination of age, normal wear, and operating conditions. Most appliance components have a predictable service life — when they exceed it, failure rates climb sharply. This is a more involved failure that may have developed over an extended period. With a 60% diagnostic match, replacing this part is the recommended first step.
60%
Diagnostic match rate
Low
DIY success rate
1-2 hours
Typical repair time
🛡️ Prevention Tips
How to prevent your washing machine's loud noise during spin from happening again after this repair.
Check inlet and drain hoses for bulging, cracking, or leaks every 3 months — replace any hose that's over 5 years old regardless of condition.
Don't overload the drum. Overloading puts excess strain on the motor, drive belt, and bearings, accelerating wear on every moving part.
Leave the door or lid open between loads to prevent mold and mildew buildup on seals and gaskets.
Use the correct amount of HE detergent — excess suds force the pump to work harder and can cause premature drain pump failure.
After completing this repair, make a note of the date and the part replaced. Tracking repairs helps you spot recurring issues before they become major failures.
Other Washing Machine Problems
Common Questions About This Repair
How much does it cost to fix a washing machine that's loud noise during spin?
How long does this washing machine repair take?
What if this isn't the problem?
Should I just replace my washing machine instead?
🔧 Repair Data Sources
Repair guides are compiled from:
- • Manufacturer service manuals and technical bulletins
- • Common failure pattern data from appliance repair technicians
- • OEM parts databases for exact replacement compatibility
Difficulty ratings are based on the average homeowner's skill level, not professional standards. Confidence percentages reflect the likelihood that the listed cause matches the observed symptom. Updated May 2026.
Disclaimer: This repair guide is for informational purposes only and is based on manufacturer service manuals and published repair data. TheFixGuide is not responsible for any damage, injury, or loss resulting from attempted repairs. If a repair involves gas, high voltage, stored energy (capacitors), or refrigerant, we strongly recommend hiring a licensed professional.
🔨 Need tools? Get parts on Amazon
Get Parts →Dex A. Varland
Master Appliance Technician · 15+ Years Experience
Dex A. Varland is a master appliance technician with 15+ years of hands-on experience across all major brands. He has diagnosed and repaired thousands of household appliances and contributes to TheFixGuide to help homeowners tackle repairs with confidence.
About TheFixGuide →Your DIY Repair Toolkit
These 3 tools cover 90% of appliance repairs.
Digital Multimeter — Electrical Tester
The single most important diagnostic tool for any appliance repair. Check continuity, voltage, and current to pinpoint electrical faults fast.
Shop Multimeters on Amazon →Appliance Repair Screwdriver Set (Torx + Philips)
Most appliances use Torx or security bits you will not find in a standard drawer. A dedicated set means no stripped screws and faster teardowns.
Shop Screwdriver Sets on Amazon →Socket Wrench Set (Metric + Standard)
From dryer lint-trap screws to washing-machine motor bolts, a socket set covers the fasteners a screwdriver cannot. Metric and standard both — appliances use both.
Shop Socket Wrench Sets on Amazon →